代码编织梦想

        炼得『剑心』之人,能视天地为丹田,化肉体为经络。被视为『武』道本源的『炁』,更不必藏身。

         新人写帖子,仅供内部人员参照

        基本配置与在下A板杀手,请赐教一样,本章涉及相关的概念与知识推荐这篇文章——PID超详细教程——PID原理+串级PID+C代码+在线仿真调参h

好啦,进入正题开始ctrl + c  ctrl + v 代码 

mian.c

/* USER CODE BEGIN Header */
/**
  ******************************************************************************
  * @file           : main.c
  * @brief          : Main program body
  ******************************************************************************
  * @attention
  *
  * Copyright (c) 2022 STMicroelectronics.
  * All rights reserved.
  *
  * This software is licensed under terms that can be found in the LICENSE file
  * in the root directory of this software component.
  * If no LICENSE file comes with this software, it is provided AS-IS.
  *
  ******************************************************************************
  */
/* USER CODE END Header */
/* Includes ------------------------------------------------------------------*/
#include "main.h"
#include "can.h"
#include "gpio.h"
 
/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */
#include "LRJ_3508.h"
#include "LRJ_PID.h"
/* USER CODE END Includes */
 
/* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD */
int16_t ref_speed,inf_speed;
int16_t pid_output;
/* USER CODE END PTD */
 
/* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */
/* USER CODE END PD */
 
/* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM */
 
/* USER CODE END PM */
 
/* Private variables ---------------------------------------------------------*/
 
/* USER CODE BEGIN PV */
 
/* USER CODE END PV */
 
/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
/* USER CODE BEGIN PFP */
 
/* USER CODE END PFP */
 
/* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 */
 
/* USER CODE END 0 */
 
/**
  * @brief  The application entry point.
  * @retval int
  */
int main(void)
{
  /* USER CODE BEGIN 1 */
 
  /* USER CODE END 1 */
 
  /* MCU Configuration--------------------------------------------------------*/
 
  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();
 
  /* USER CODE BEGIN Init */
 
  /* USER CODE END Init */
 
  /* Configure the system clock */
  SystemClock_Config();
 
  /* USER CODE BEGIN SysInit */
 
  /* USER CODE END SysInit */
 
  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  MX_CAN1_Init();
  /* USER CODE BEGIN 2 */
  //ref_speed = 1000; 
	init_m3508_can();//开启过滤器
	PIDInit(&M3508_spid[0],5,0,0,15000,15000);//速度环设置和限幅   spid:15  0.5  0
    PIDInit(&M3508_apid[0], 0.05,0,0,10000,10000);//位置环设置和限幅apid:0.05  0  0
  /* USER CODE END 2 */
 
  /* Infinite loop */
  /* USER CODE BEGIN WHILE */
  while (1)
  {
    PID_Position_Calc(&M3508_apid[0], m3508_fback_inf[0].total_angle, m3508_fback_inf[0].set_angle);//位置环
    PID_Incremental_Calc(&M3508_spid[0], m3508_fback_inf[0].speed, M3508_apid[0].output);//速度环
	m3508_fback_inf[0].control_current = M3508_spid[0].output;
    send_m3508_control_current();
    HAL_Delay(5);//有bug必须搞个5ms延时,或者开个定时器中断丢中断里头
    /* USER CODE END WHILE */
 
    /* USER CODE BEGIN 3 */
  }
  /* USER CODE END 3 */
}
 
/**
  * @brief System Clock Configuration
  * @retval None
  */
void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
 
  /** Configure the main internal regulator output voltage
  */
  __HAL_RCC_PWR_CLK_ENABLE();
  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
 
  /** Initializes the RCC Oscillators according to the specified parameters
  * in the RCC_OscInitTypeDef structure.
  */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLM = 6;
  RCC_OscInitStruct.PLL.PLLN = 180;
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
  RCC_OscInitStruct.PLL.PLLQ = 4;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    Error_Handler();
  }
 
  /** Activate the Over-Drive mode
  */
  if (HAL_PWREx_EnableOverDrive() != HAL_OK)
  {
    Error_Handler();
  }
 
  /** Initializes the CPU, AHB and APB buses clocks
  */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
 
  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
  {
    Error_Handler();
  }
}
 
/* USER CODE BEGIN 4 */
 
/* USER CODE END 4 */
 
/**
  * @brief  This function is executed in case of error occurrence.
  * @retval None
  */
void Error_Handler(void)
{
  /* USER CODE BEGIN Error_Handler_Debug */
  /* User can add his own implementation to report the HAL error return state */
  __disable_irq();
  while (1)
  {
  }
  /* USER CODE END Error_Handler_Debug */
}
 
#ifdef  USE_FULL_ASSERT
/**
  * @brief  Reports the name of the source file and the source line number
  *         where the assert_param error has occurred.
  * @param  file: pointer to the source file name
  * @param  line: assert_param error line source number
  * @retval None
  */
void assert_failed(uint8_t *file, uint32_t line)
{
  /* USER CODE BEGIN 6 */
  /* User can add his own implementation to report the file name and line number,
     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
  /* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */

在debug里位置环的p数值不要给大,给好一个值就不要再去改动,调速度环的。

剩下的自己去debug里玩去吧,老师傅我累了,今天就更这么多。

明天更新遥控。敬请期待

版权声明:本文为博主原创文章,遵循 CC 4.0 BY-SA 版权协议,转载请附上原文出处链接和本声明。
本文链接:https://blog.csdn.net/m0_65642869/article/details/126984109

java手游 《剑心》_剑心无尘官方正版手游-剑心无尘官方正版手游安卓最新v1.4.3下载 - 手机迷...-爱代码爱编程

剑心无尘官方正版手游中各种精彩刺激的战斗将会在这里一触即发,这是一款超级残酷的修仙手游玩家们在游戏中只有通过自己的不断努力才能够获得更加强大的实力一开始你只是一个默默无闻的小角色偶然之下获得了机遇让你在游戏中突然实力大增体验到各种不一样的精彩乐趣喜欢这款游戏的玩家们将会在这里感受到一个全新不一样的精彩冒险世界欢迎各位玩家们一起加入到这款有趣的游戏中。

剑心 十字伤-爱代码爱编程

在日本明治维新,战争多发,生灵涂炭的乱世背景下,浪客剑心,讲述了一个男孩成长为男人的故事。 如果单单说十字伤,其实更多人第一个反应可能是,这表面上是脸上的刀疤,啊,这就是人生的阅历,啊,这就是岁月的洗礼,啊,这就是成熟男人的魅力。那么我们要是再说一个条件,这个刀疤他不是一次弄出来的,这是先后各一刀——那其实和没说一样,这不废话,反正不都是人生的阅历经历嘛